Optimization and efficiency analysis of methanol SOFC-PEMFC hybrid system

In order to improve the power generation efficiency of fuel cell systems employing liquid fuels, a hybrid system consisting of solid oxide fuel cell (SOFC) and proton exchange membrane fuel cell (PEMFC) is proposed. Utilize the high temperature heat generated by SOFC to reform as much methanol as possible to improve the overall energy efficiency of the system. When SOFC has a stable output of 100 kW, the amount of hydrogen after reforming is changed by changing the methanol flow rate. Three hybrid systems are proposed to compare and select the best system process suitable for different situations. The results show that the combined combustion system has the highest power generation, which can reach 350 kW and the total electrical efficiency is 57%. When the power of the tail gas preheating system is 160 kW, the electrical efficiency can reach 75%. The PEM water preheating system has the most balanced performance, with the electric power of 300 kW and the efficiency of 66%.     

Thermal destratification of cryogenic liquid storage tanks by continuous bubbling of gases

This paper focuses on thermal destratification and pressurisation inside thermally stratified storage tanks by continuous gas bubbling. The primary purpose of doing these studies is to better understand the effect of bubble dynamics on thermal destratification and quantify the extent of destratification. The volume of fluid and interface compression method of OpenFOAM CFD code is utilised for the present analysis. Different values of inlet gas velocities (V_g), orifice diameters (d_o), and arrangement of the orifices in triangular and square fashion with different pitches (p/d_o) are considered. In addition, the effect of gravitational forces (g/g_e) on thermal destratification is also reported. For all these cases, the effectiveness of thermal destratification is quantified in terms of a newly defined parameter, the destratification index (I_d). For V_g = 1 m/s, the I_d value is maximum compared to lower V_g values. It is seen that when the gas velocity increased from 0.3 m/s to 1.0 m/s, the average effectiveness in thermal destratification (I_davg) and pressure at the ullage increased by 44.38% and by 64.81%, respectively. The I_davg and pressure at ullage increased by 96.29% and 14.91%, respectively, when the g/g_e ratio changed from 0.3 to 3. Compared to the triangular arrangement with p/d_o = 10, the calculated I_davg increased by 30.67% when gas inlets were arranged with a square pitch of 10. For p/d_o = 4, 6 and 8, the increments in I_davg are of the order of 12.86%, 19.43% and 21.92%, respectively, for gas inlets arranged in a square fashion as compared to the triangular arrangement. It is found that continuous bubbling with gas inlets arranged in square pitch p/d_o = 10 gives higher effectiveness in thermal destratification. Thus, by these studies, one can develop a thermal destratification mechanism with continuous bubbling for optimum performance. Also, these studies give an overall idea of sparger design for getting the correct gas flow rate for thermal destratification within the cryogenic liquid storage tanks.     

Effect of catalytic washcoat shape and properties on mass transfer characteristics of microstructured steam-methanol reformers for hydrogen production

Many attempts have been made to improve mass transfer by reducing the size of reactors. However, such reduction will fairly quickly reach practical limitations and numerous difficulties still remain. Catalytic washcoat shape and properties may be critical design factors, but the mechanisms for their effects on mass transfer characteristics are still not fully understood. To effectively eliminate problems associated with mass transport phenomena in microstructured steam-methanol reformers, the effects of washcoat shape and properties were investigated in various situations by performing computational fluid dynamics simulations. The dependence of the solution on mass transfer characteristics was reduced to a small number of dimensionless parameters. A dimensionless mass transfer analysis was carried out in terms of the Sherwood, Schmidt, and pore Reynolds numbers. The results indicated that the rate of mass transfer is predominantly controlled by washcoat properties, and porosity and effective thermal conductivity are fundamentally important. The rate of the reforming reaction is typically controlled by kinetics at a temperature of 480 K and limited by mass transfer at a temperature of 580 K. The shape of washcoats affects the overall mass transfer characteristics, depending on the structural and thermal properties of washcoats. The shape effect is limited by heat transfer. A three-fold increase in effectiveness factor can be achieved by increasing the effective thermal conductivity of the washcoat. Design recommendations were finally made to improve transport characteristics for the systems.     

C105管桩混凝土设计参数取值的探讨

通过试验得出了C105混凝土100 mm×100 mm×100 mm立方体非标准试件抗压强度换算系数以及C105混凝土的标准方差和强度变异系数。采用理论计算,得到了棱柱体抗压强度与立方体抗压强度的比值α_c1,并与试验实测平均值进行了比较,验证了理论计算方法的可行性。此外,通过对比分析,探讨了直接外延法和引用公式法两种C105混凝土设计参数计算方法的正确性,研究结果可为C105管桩混凝土的设计和应用提供参考。     

Can regional policies shape migration flows?

Our empirical analysis focuses on the effect of regional policies on migration attraction factors in Europe. We employ a regression discontinuity design to assess the causal relationship between the reception of large amounts of public funds and migration flows in the EU-15 regions. In highly-subsidised regions, we find a large increase in the share of foreign citizens from less-developed countries when compared to low-subsidised regions with similar pre-treatment characteristics. The analysis shows that such an increase is due to the positive impact of the European regional policy on job market opportunities as well as the improvement of public goods supply.     

No-Reference Video Quality Assessment using novel hybrid features and two-stage hybrid regression for score level fusion

This paper presents a novel No-Reference Video Quality Assessment (NR-VQA) model that utilizes proposed 3D steerable wavelet transform-based Natural Video Statistics (NVS) features as well as human perceptual features. Additionally, we proposed a novel two-stage regression scheme that significantly improves the overall performance of quality estimation. In the first stage, transform-based NVS and human perceptual features are separately passed through the proposed hybrid regression scheme: Support Vector Regression (SVR) followed by Polynomial curve fitting. The two visual quality scores predicted from the first stage are then used as features for the similar second stage. This predicts the final quality scores of distorted videos by achieving score level fusion. Extensive experiments were conducted using five authentic and four synthetic distortion databases. Experimental results demonstrate that the proposed method outperforms other published state-of-the-art benchmark methods on synthetic distortion databases and is among the top performers on authentic distortion databases. The source code is available at https://github.com/anishVNIT/two-stage-vqa.     

模具设计与制造专业群虚拟仿真实训基地建设路径研究

针对模具设计与制造专业群实训教学开展过程中存在的问题,开展专业群虚拟仿真实训基地的建设,通过精密模具智能制造生产线仿真实训工厂、模具数字化设计及智能成型单元综合应用平台、开放共享课程资源等3个方面内容的建设,引入行业新技术、新工艺、新标准,确保虚拟仿真教学资源与学生职业能力培养相一致。基地建设依托智能制造新技术,以培养高层次复合型技术技能人才为主线,满足实训教学为核心,多方共享为目标,助力区域经济发展,服务"鲁班工坊"国际化建设,最终实现虚拟仿真实训基地区域示范性效果。     

智能数据分区与布局研究

大数据时代,数据规模庞大,由数据进行驱动的应用分析场景日益增多.如何快速、高效地从这些海量数据中提取出用以分析决策的信息,给数据库系统带来重大挑战.同时,现代商业分析决策对分析数据的实时性要求数据库系统能够同时快速处理ACID事务和复杂的分析查询.然而,传统的数据分区粒度太粗,且不能适应动态变化的复杂分析负载;传统的数据布局单一,不能应对现代大量增加的混合事务分析应用场景.为了解决以上问题,“智能数据分区与布局”成为当前的研究热点之一,它通过数据挖掘、机器学习等技术抽取工作负载的有效特征,设计最佳的分区策略来避免扫描大量不相关的数据,指导布局结构设计以适应不同类型的工作负载.首先介绍了智能数据分区与布局的相关背景知识,然后对智能数据分区与布局技术的研究动机、发展趋势、关键技术进行详细的阐述.最后,对智能数据分区与布局技术的研究前景做出总结与展望.     

江西省水系连通及水美乡村建设试点县实施方案编制存在的问题及对策

为提高水系连通及水美乡村建设试点县实施方案编制质量，更好地参加全国竞争性立项，本文分析研究了江西省55个水系连通及水美乡村建设试点县实施方案和相应的专家评审意见，对实施方案编制过程中存在的符合性、完整性不够，实施范围情况调查不准等七个方面突出问题进行梳理剖析，并提出相应对策，可为实施方案编制提供参考。